Six, PF109 oil filling special antistatic anticorrosive coating: waterproofing singaporeSuitable for oil storage irrigation, special antistatic anticorrosive coating, suitable for oil storage irrigation, (including gasoline, diesel, kerosene, crude oil, aviation oil) wall corrosion and will not generate static electricity, there is absolutely reliable security, antiseptic spray 3 -5 times the amount of 0.8 kilograms per square meter. waterproofing singaporeSeven, H88-1 epoxy rust paint: Applicable to all kinds of steel corrosion, without sand-blasting, construction convenient, good preservative effect. H88-1 primer brushing two dosage 0.4 kilograms per square meter. H88-2 finish brushing three dosage 0.6 kilograms per square meter. Eight, PL pipeline anti-corrosion coating (ie bituminous coal tar epoxy paint): waterproofing singaporeApplicable to all kinds of underground oil, gas and water pipelines against corrosion, can be a three-coat cloth, two cloth six coating, the coating has good electrical insulation properties. waterproofing singaporeRunway Road panel joints and other occasions. Rigid waterproof waterproofing singaporeExtending the use of higher strength and non-waterproof material, such as waterproof mortar, composed of waterproof concrete waterproofing layer. Depend on the density of the structural member itself or rigid material for the waterproof layer in order to achieve the purpose of the building is called a rigid waterproof waterproof. Stones on a building grassroots waterproof membrane or coating waterproof coating, waterproof isolation layer so as to form, which is commonly referred to as flexible waterproof, commonly known as “temporary” foreign waterproof technology. Flexible Then interface with waterproof material must not have swelling drums, from sand, honeycomb, wood, paper, sludge, small stones, can not do on the loose shaky table body, because poor adhesion, plus the sun UV damage, the building itself is heating or cooling, and vapor pressure damage, is likely to cause the waterproof layer of aging, failed.waterproofing singapore(Four) positive than negative waterproof waterproof: waterproofing singaporeSuch as roofing, directly on the roof surface, the walls should be done directly in the exterior waterproofing, water leaking directly on the inner tank, the water pressure would go to his office diffusion, the house where the dead are not easily applied waterproofing singaporeRevision: 1 Printing: Pages: 460 Word Count: 750,000 Summary Engaged in construction work friends, most contact information is also the most necessary standards. As of 2005 the construction of the existing standards, norms, rules 1162. Among them: mandatory provisions 3, 311 national standards for construction, urban construction engineering industry standard 102, the industry standard 143 construction projects, construction of industrial product standards 334, China Engineering Construction Standardization Association Standard 175, project construction standards 94. Construction workers should all be familiar with these standards is almost impossible! Not even know all of the standard name. waterproofing singaporeThe book accordance with the technical standards, product standards, project construction standard sort, and then follow the standard number for secondary sort, a collection of standards and waterproof relevant national standards, industry standards, technical standards. Product Overview Modified bitumen membrane (SBS membrane). 2, plastic modified bitumen waterproofing membrane (APP membrane). 3, self-adhesive polymer modified bitumen membrane (APF coil). 4, synthetic polymer waterproofing membrane waterproofing singapore 2.1: SBS membrane: SBS rubber modified asphalt is cited as maceration cover, non-woven polyester fibers, jute, glass fiber mat, respectively, for the tire production base, in order to isolate the layer of plastic film for release by selection, ingredients, eutectic, maceration, composite molding, curling and other processes to manufacture. SBS modified bitumen membrane, the membrane has good high temperature performance, can be used within -25 degrees to + 100 ℃ temperature range, with high elasticity and resistance to fatigue, and up to 1500% of elongation and strong resistance to puncture the ability to tear resistance capability. Suitable for cold areas, as well as large deformation and vibration waterproof industrial and civil engineering. Features: low temperature flexibility, reach -25 ℃ not crack; high heat resistance, 100 ℃ not flowing. Good extends performance, long life, simple construction, low pollution. Products applicable to I, II grade waterproofing buildings, especially for low temperature cold regions and structural deformation frequent construction waterproofing. Specifications Category: divided by physical indicators: I (-20 ℃), II (-http://www.allstarwaterproofing.com.sg/